Sub-Zero Ice Maker Not Working, or Making Hollow Cubes
If your Sub-Zero fridge is not making ice, the cause is usually something that stops the ice maker without anything being broken: the ice maker is switched off, the shut-off arm is up, the water supply or filter is restricting flow, or the freezer is too warm. Sub-Zero says a new or restarted ice maker can take 24 hours to show cubes in the bin, so give it a day before you call. When those checks pass and there is still no ice, a frozen fill tube, the water valve or the ice maker itself needs a diagnosis.
- What it means
- The ice maker is off, blocked, not getting water, or the freezer is not cold enough to freeze the cubes
- Check first
- Ice maker switched on, shut-off arm down, ice bin seated, water supply open, filter reseated, freezer at 0°F
- Normal output
- Sub-Zero rates a freezer ice maker at about 8 cubes every 2 to 3 hours; a full bin can take 1 to 2 days
- Labour
- From $180
- Parts
- Priced after the diagnosis, before any work starts
- Diagnostic visit
- $79, waived when you go ahead with the repair
- Where we work
- Toronto, North York, York, East York, Etobicoke and Mississauga
Why is my Sub-Zero ice maker not working?
A Sub-Zero fridge stops making ice when one link in a short chain breaks: water has to reach the ice maker, the freezer has to be cold enough to freeze it, and the ice maker has to be allowed to run. The ice maker fills its mould through a small fill tube, freezes the water and drops the cubes into the bin, where a shut-off arm stops production once the bin is full.
That arm is the most common reason a working ice maker goes quiet. If it is knocked up by the bin or a bag of frozen food, the ice maker thinks the bin is full and stops. Sub-Zero notes the arm only moves about an inch, and on some models the bin itself presses the ice maker switch, so a bin that is not level and fully seated can switch the ice maker off as well.
Temperature is the next link. Sub-Zero recommends a freezer setting of 0°F and says ice production suffers once the freezer is warmer than 5°F. A freezer that has crept up because the condenser is dusty can still feel cold and yet stop making ice.
What stops a Sub-Zero ice maker from making ice?
| Cause | What you notice | What fixes it |
|---|---|---|
| Ice maker off or just restarted | No ice cube symbol on the display, or the unit was switched on within the last day | Turning the ice maker on and waiting 24 hours |
| Shut-off arm up or bin not seated | The arm is raised; the bin sits crooked or slightly forward | Lowering the arm gently and seating the bin level |
| Water supply or filter | Supply valve closed, filter overdue, or cubes small and hollow | Opening the valve, reseating or replacing the filter; low house pressure needs a plumber |
| Freezer too warm | Freezer above 5°F on the display; condenser not cleaned in months | Cleaning the condenser and setting the freezer to 0°F |
| Frozen fill tube or jammed cube | Ice build-up around the ice maker; the mould stays empty | Clearing the jam or defrosting the freezer manually |
| Water valve or ice maker fault | Every check passes and there is still no ice after 24 hours | Diagnosing and replacing the failed part |
Why are my Sub-Zero ice cubes hollow or small?
Hollow or undersized cubes are a water and temperature question rather than a jam. Sub-Zero lists two causes for it — warm freezer temperatures and an ice maker issue — and the checks run in that order: confirm no service messages, icons or error codes are showing, then check the freezer is below 5°F, keeping in mind that 0°F is the recommended setting and that anything above 5°F affects ice maker performance.
After that it is the water side. Sub-Zero asks you to verify the condenser has been cleaned within the last three to six months, to rule out any recent plumbing or water pressure problems in the house, and to make sure an in-line filter has not expired — some models have a filter built in, others take an external one. Even where house pressure is fine, sediment in the supply line can cut the pressure reaching the unit, and genuinely low pressure is a plumber's job rather than an appliance repair.
How to fix the ice maker in a Sub-Zero refrigerator yourself
Work through these in order:
- Confirm the ice maker is on. On many models a single or triple ice cube symbol shows on the display when it is on. No symbol means it is off.
- Lower the shut-off arm and seat the bin. If the arm is up, switch the unit off and push the arm down gently. Slide the bin back in so it sits level and fully home.
- Check the freezer temperature. Set it to 0°F. If the display reads warmer than 5°F, look at the condenser: Sub-Zero recommends cleaning it if it has not been done in the past 6 to 12 months.
- Check the water. Make sure the supply valve to the fridge is open. Switch the power off, take the water filter out and put it back in, even if it is not due. Replace it if it is past its date.
- Look for ice build-up. If cubes are jammed in the ice maker or ice has formed around the fill tube, Sub-Zero's guidance is to defrost the freezer manually to clear it.
- Reset and wait. Switch the unit off and on again, then give it 24 hours. Water may not flow into the ice maker immediately after it is turned on.
Call a technician if the freezer will not come down to 0°F, if the fill tube freezes again soon after a defrost, if no water reaches the mould even with the supply open and the filter reseated, or if the ice maker stays empty a day after every check has passed.
What we see on Sub-Zero ice maker calls
- Where
- Toronto, North York, York, East York, Etobicoke and Mississauga
- Machine
- Sub-Zero built-in and freestanding refrigerators with a freezer ice maker
- Technician
- Andrew, appliance repair technician, 4+ years in the field
“When a Sub-Zero fridge stops making ice, I check the freezer temperature and the shut-off arm before anything else, because either one stops the ice maker without a single part being broken.”— Andrew, our technician on these calls
Do you fix Sub-Zero refrigerators in my area?
Yes. We repair Sub-Zero refrigerators and ice makers in Toronto, North York, York, East York, Etobicoke and Mississauga, and we service Sub-Zero appliances across the rest of the GTA and Simcoe County: 29 areas, same day in most of them, seven days a week, with no travel surcharge.
Questions we get about Sub-Zero fridges that stop making ice
Why is my Sub-Zero ice maker not working after it was switched back on?
It may simply need more time. Sub-Zero says it can take 24 hours to see cubes in the bin, because the freezer has to cool down first, and water may not flow into the ice maker immediately after it is turned on. A full bin can take 1 to 2 days.
Why does my Sub-Zero refrigerator have ice build-up around the ice maker?
Ice packed around the ice maker or a frozen fill tube stops water from reaching the mould, so no new cubes form. Sub-Zero's guidance is to defrost the freezer manually to clear it. If the build-up comes back soon after a defrost, have the fridge checked.
How do I reset a Sub-Zero ice maker?
Switch the unit off and on again, then wait 24 hours. On Classic models with a flashing single ice cube on the display, Sub-Zero says to hold the Alarm key for 15 seconds until the display reads CFC, and if it still flashes, hold the Max Ice and Ice Maker keys together for 5 seconds.
How much does it cost to fix a Sub-Zero fridge that is not making ice?
Labour starts at $180. The part depends on what the diagnosis finds, so we price it once we know what failed. The $79 diagnostic is waived when you go ahead.