Fisher & Paykel Dishwasher Beeping 3 or 4 Times: Causes
Swift Appliance Solution
MON–SUN from 8:00AM to 8:00PM
(647) 846-7077

Why Is My Fisher & Paykel DishDrawer Beeping? Codes & Lights

By Andrew, appliance repair technician, 4+ years in the fieldUpdated November 7, 2026

A Fisher & Paykel DishDrawer that beeps 3 or 4 times when you pause it is giving its normal pause signal. One that beeps without stopping has found a fault, and the flashing lights or the code in the display tell you which one. Beeping that comes and goes usually means a drawer was paused and never restarted. Most of the time the code points to something you can check yourself.

Fisher & Paykel dishwasher beeping at a glance
Beeping 3 or 4 times
The pause signal: three short tones and one long tone. Wait for it before opening the drawer
Continuous beeping
A fault: an A or F code in the display, or a pattern of flashing lights on models without one
Beeping on and off
The drawer is paused. Close it and press Start
Check first
The code or the lights that are flashing, the water supply, the drain hose and the spray arm
Error codes
A1 water supply, A3 cannot drain, A6 spray arm or low water pressure. F codes need a reset
Labour
From $180
Parts
Priced after the diagnosis, before any work starts
Diagnostic visit
$79, waived when you go ahead with the repair
Where we work
Toronto, North York, York, East York, Etobicoke and Mississauga

Why does my Fisher & Paykel dishwasher keep beeping?

The first thing to notice is the rhythm. Fisher & Paykel's user guide separates two kinds of beeping: continuous beeping means a fault has occurred, and intermittent beeping means the dishwasher is paused. For a pause, close the drawer and press Start.

Continuous beeping is the dishwasher reporting a problem it found itself. When a Fisher & Paykel dishwasher stops and beeps mid-wash, something is wrong: no water coming in, water that cannot get out, or a spray arm off its mounting. On a double model you can keep using the drawer without the fault.

Why is my Fisher & Paykel DishDrawer beeping 3 or 4 times?

A short burst of beeps right after you press pause is the DishDrawer telling you it is safe to open. Fisher & Paykel's guide says to wait for three short tones and one long tone before opening the drawer. Depending on whether you count the long tone, that sounds like beeping 3 times or 4 times, and it does not mean a fault.

A paused drawer is also the most common reason for beeping that will not go away, and it is easy to cause by accident. If the drawer is not restarted within 7 minutes, it keeps sounding a tone on and off until it is. So a DishDrawer that seems to beep for no reason is often a drawer that was opened mid-wash, closed again and left waiting. Close it firmly and press Start.

What do Fisher & Paykel dishwasher error codes and flashing lights mean?

On models with a display, the fault code flashes there and the drawer indicator flashes to show which drawer has the fault. On models without a display, the DishDrawer error lights are the code: Fisher & Paykel's guide says that if the wash modifier and lock indicators flash, it is an F fault, and if only the wash modifier indicators flash, it is an A fault. One or more wash program indicators also light up to tell you which code it is. On some current models, for example, Rinse plus all modifiers means A1, and Delicate and Rinse plus all modifiers means A3.

CauseWhat you noticeWhat fixes it
Drawer pausedBeeping on and off; the wash stopped partwayClosing the drawer firmly and pressing Start to resume
A3: drawer cannot drainContinuous beeping, water left in the drawerClearing the drain hose and its connection to the pipes, then the filters
A1: water supply faultContinuous beeping, the drawer stays dryTurning the water supply on, then clearing the code
A6: spray arm or water pressureContinuous beeping, the spray arm is loose or offRefitting the spray arm so it is firmly seated and turns freely
Rinse aid lowThe rinse aid indicator glows or flashes bright redRefilling the rinse aid dispenser
F faultContinuous beeping with an F code, or the lock and modifier lights flashingA reset; if the code comes back, a technician
Fisher & Paykel dishwasher beeping and stopped mid-wash? We can usually be out today.
Call (647) 846-7077 Text us

How to stop a Fisher & Paykel dishwasher beeping yourself

Write the code down before you clear anything: you will need it if the fault returns.

  1. Listen to the rhythm. On and off means a paused drawer: close it firmly and press Start. Continuous beeping means a fault, so move on to the next step.
  2. Read the code. Note the letter and number in the display, or which lights are flashing on a model without one. On a double model, check both drawers, because each can show a different code.
  3. For A1, check the water supply. Make sure the supply valve to the dishwasher is turned on. Then clear the code as your guide shows: one press stops the beeping, a second press clears the fault, and you resume the wash.
  4. For A3, check the drain path. Look for a kinked or blocked drain hose under the sink and a blocked connection to the drain pipe, then clean the filters. Clear the code the same way.
  5. For A6, check the spray arm. Open the drawer and refit the spray arm if it has loosened or come off its mounting. It should sit firmly and turn freely.
  6. For an F code, reset the dishwasher. Press the power button to stop the beeping, press it again to switch the dishwasher off, wait a few seconds, then switch it back on. If the code has gone, the fault has been reset.

Call a technician if an F code comes back after a reset, if an A code returns as soon as you resume, if both drawers show faults, or if you find water underneath the dishwasher. With a leak, turn off the water and the power to the dishwasher before anything else.

What we see on Fisher & Paykel dishwasher beeping calls

Where
Toronto, North York, York, East York, Etobicoke and Mississauga
Machine
Fisher & Paykel dishwashers, including single and double DishDrawer models
Technician
Andrew, appliance repair technician, 4+ years in the field
“When a Fisher & Paykel dishwasher keeps beeping, the first thing I check is whether it beeps nonstop or on and off: that tells me if it is a fault code or just a paused drawer.”— Andrew, our technician on these calls

Do you fix Fisher & Paykel dishwashers in my area?

Yes. We repair beeping and flashing Fisher & Paykel dishwashers in Toronto, North York, York, East York, Etobicoke and Mississauga, and across the rest of the GTA and Simcoe County: 29 areas, same day in most of them, seven days a week, with no travel surcharge.

Same code back after a reset? Book a technician for today.
Call (647) 846-7077

Questions we get about Fisher & Paykel dishwashers that beep

My Fisher & Paykel dishwasher is beeping 4 times. Is something wrong?

Usually not. When you pause a wash, Fisher & Paykel says to wait for three short tones and one long tone before opening the drawer, which many people hear as 3 or 4 beeps. Continuous beeping is different and means a fault.

Why is my Fisher & Paykel DishDrawer beeping on and off?

The drawer is paused. If a paused drawer is not restarted within 7 minutes, it sounds a tone on and off until it is. Close the drawer firmly and press Start to resume the program.

Can I turn off the beeps on a Fisher & Paykel dishwasher?

Yes. The tones are a setting in the preferences menu. Turning them off silences every tone except fault alerts. The button combination is in your model's guide.

How much does it cost to fix a Fisher & Paykel dishwasher that keeps beeping?

Labour starts at $180. The part depends on what the diagnosis finds, so we price it once we know what failed. The $79 diagnostic is waived when you go ahead.

Swift Appliance Solution
×
MON–SUN from 8:00AM to 8:00PM
(647) 846-7077
Request a callback
Get a call in 5 minutes

Leave your number and our dispatcher will call you back right away — Mon–Sun, 8 AM to 8 PM.

✓ No spam. By submitting you agree to our Privacy Policy.
or call us now: (647) 846-7077
✓
We're dialing!
Expect our call within 5 minutes.